Enterasys-networks XSR-3020 Manual do Utilizador descarregar pdf (Página 100)

Cable, CompactFlash and Accessory Specifications

A-14

Installing Shunt/Terminal Strip

To install the shunt or terminal strip, attach two dual-pin units vertically to each four-pin jumper

(P2, P3, P4, or P5) corresponding to the RJ-48C port using a balun, as shown in Figure A-16. Any

other RJ-48C ports on the NIM card connected to 120-ohm lines do not require shunts.

Figure A-16 Installing a Grounding Shunt on the E1 NIM Card

1 2 ... 95 96 97 98 99 100 101 102 103 104 105 ... 109 110

X-Pedition 1
Security Router 1
Industry Canada Notices 5
Class A ITE Notice 5
Clase A. Aviso de ITE 5
Klasse A ITE Anmerkung 5
orcontact 6
(Circuit Modules) 7
(Circuit Breakers) 7
VCCI Notice 8
BSMI EMC Statement — Taiwan 8
Declaration of Conformity 8
Australian Telecom 9
Contents 13
Appendix A: Specifications 15
About This Guide 17
Getting Help 19
Overview 21
PSTN (for PPP) 22
ETH2ETH1 23
Operating System 24
Industry-common CLI 24
IP Protocol 24
IP Routing 25
SNMP and Statistics Gathering 25
Security 26
Frame Relay 26
System Description 27
XSR Getting Started Guide 1-7 27
Quality of Service (QoS) 28
Virtual Private Network (VPN) 28
GRE over IPSec 29
Dial Service 30
Dial Backup 30
Installation Overview 31
1-12 Overview 32
Hardware Installation 33
2-2 Hardware Installation 34
XSR Getting Started Guide 2-3 35
2-4 Hardware Installation 36
XSR Getting Started Guide 2-5 37
2-6 Hardware Installation 38
Connecting Cables 39
SECURITY ROUTERS 40
XSR Getting Started Guide 2-9 41
Figure 2-16 42
Figure 2-18, respectively 43
Software Configuration 44
Initializing XSR Software 46
3-2 Software Configuration 46
XSR Getting Started Guide 3-3 47
Setting the Clock 51
Configuring the LAN Ports 52
Configuring the WAN Ports 52
BRI Leased Line 53
BRI Leased Frame Relay 53
BRI Switched Line 54
Firewall Sample Configuration 56
Setting Up RIP Routing 58
Configure OSPF Routing 59
3-16 Software Configuration 60
Viewing Your Configuration 61
3-18 Software Configuration 62
Site regional router 64
Configure Users and Passwords 66
Configure LAN Interface 66
Configure Quality of Service 66
Apply QoS 68
Configure More Access Lists 68
Configure DHCP/BOOTP Relay 69
Configure SNMP 70
Set Up IKE Phase I Security 71
Create a Transform Set 72
Configure Crypto Maps 72
3-30 Software Configuration 74
XSR Rebooting Characteristics 76
Reboot Triggers 77
Cause Boot Type 77
3-34 Software Configuration 78
Bootrom Monitor Mode Commands 79
3-36 Software Configuration 80
3-38 Software Configuration 82
3-40 Software Configuration 84
3-42 Software Configuration 86
Specifications 87
Short-haul MTRJ 88
Pin 1 Pin 5 90
Pin 6 Pin 9 90
Pins not shown are unused 96
RX In TX Out 99
G.703 Balun 99
Model 460 MC 99
Regulatory/Safety Compliance 101
ALARM LOS 101
ENABLE LOF 101
Port 0 Activation LED 102
Port 1 Activation LED 102
Pin 8Pin 1 102
Transmit Pair Termination 103
Port 0 Port 1 103
Port 1Port 0 103
Receive Pair Termination 103
NIM1 NIM2 107
LED State Function 108
Index-2 110

Comentários a estes Manuais

Sem comentários

Enterasys-networks XSR-3020 Manual do Utilizador Página 100

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Enterasys-networks XSR-3020